9879开启PUIS导致机械硬盘丢失现象与修复汇总(12.10 KB3021937补丁，彻底修复，完结)

wangbolizhong

z75h 发表于 2015-1-12 20:51
这就不清楚了，反正没有折腾之心的人还是谨慎对待测试版为好。

按方法五做的，不知哪里不对没成功。有问题的硬盘在光驱位，是开机后插进去的。Ubuntu里可以访问的。
ubuntu-kylin@ubuntu-kylin:~$ sudo hdparm -s0 /dev/sd?

/dev/sda:
spin-up: setting power-up in standby to 0 (off)
HDIO_DRIVE_CMD(powerup_in_standby) failed: Input/output error
ubuntu-kylin@ubuntu-kylin:~$ sudo hdparm -s0 /dev/hd?
/dev/hd?: No such file or directory
ubuntu-kylin@ubuntu-kylin:~$ sudo hdparm -iI /dev/sd?

/dev/sda:

Model=SanDisk SDSSDHP128G, FwRev=X2316RL, SerialNo=140718402487
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=unknown, MaxMultSect=1, MultSect=1
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=250069680
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes:  pio0 pio1 pio2 pio3 pio4
DMA modes:  mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive conforms to: unknown:  ATA/ATAPI-4,5,6,7

* signifies the current active mode


ATA device, with non-removable media
        Model Number:       SanDisk SDSSDHP128G                     
        Serial Number:      140718402487        
        Firmware Revision:  X2316RL
        Media Serial Num:   
        Media Manufacturer:
        Transport:          Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
Standards:
        Used: unknown (minor revision code 0x0028)
        Supported: 8 7 6 5
        Likely used: 8
Configuration:
        Logical                max        current
        cylinders        16383        16383
        heads                16        16
        sectors/track        63        63
        --
        CHS current addressable sectors:   16514064
        LBA    user addressable sectors:  250069680
        LBA48  user addressable sectors:  250069680
        Logical  Sector size:                   512 bytes
        Physical Sector size:                   512 bytes
        Logical Sector-0 offset:                  0 bytes
        device size with M = 1024*1024:      122104 MBytes
        device size with M = 1000*1000:      128035 MBytes (128 GB)
        cache/buffer size  = unknown
        Nominal Media Rotation Rate: Solid State Device
Capabilities:
        LBA, IORDY(can be disabled)
        Queue depth: 32
        Standby timer values: spec'd by Standard, no device specific minimum
        R/W multiple sector transfer: Max = 1        Current = 1
        Advanced power management level: 254
        DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4
             Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
        Enabled        Supported:
           *        SMART feature set
                    Security Mode feature set
           *        Power Management feature set
           *        Write cache
           *        Look-ahead
           *        Host Protected Area feature set
           *        WRITE_BUFFER command
           *        READ_BUFFER command
           *        DOWNLOAD_MICROCODE
           *        Advanced Power Management feature set
                    SET_MAX security extension
           *        48-bit Address feature set
           *        Device Configuration Overlay feature set
           *        Mandatory FLUSH_CACHE
           *        FLUSH_CACHE_EXT
           *        SMART error logging
           *        SMART self-test
           *        General Purpose Logging feature set
           *        64-bit World wide name
           *        WRITE_UNCORRECTABLE_EXT command
           *        {READ,WRITE}_DMA_EXT_GPL commands
           *        Segmented DOWNLOAD_MICROCODE
           *        Gen1 signaling speed (1.5Gb/s)
           *        Gen2 signaling speed (3.0Gb/s)
           *        Gen3 signaling speed (6.0Gb/s)
           *        Native Command Queueing (NCQ)
           *        Host-initiated interface power management
           *        Phy event counters
           *        READ_LOG_DMA_EXT equivalent to READ_LOG_EXT
           *        DMA Setup Auto-Activate optimization
                    Device-initiated interface power management
           *        Software settings preservation
           *        Data Set Management TRIM supported (limit 16 blocks)
           *        Deterministic read ZEROs after TRIM
Security:
        Master password revision code = 65534
                supported
        not        enabled
        not        locked
                frozen
        not        expired: security count
                supported: enhanced erase
        2min for SECURITY ERASE UNIT. 12min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 5001b44bcf0d67b7
        NAA                : 5
        IEEE OUI        : 001b44
        Unique ID        : bcf0d67b7
Checksum: correct

/dev/sdb:
HDIO_GET_IDENTITY failed: Invalid argument

ATA device, with non-removable media
        Model Number:       WDC WD3200BEVT-22ZCT0                  
        Serial Number:      WD-WX90A6908975
        Firmware Revision:  11.01A11
        Transport:          Serial, SATA 1.0a, SATA II Extensions, SATA Rev 2.5
Standards:
        Supported: 8 7 6 5
        Likely used: 8
Configuration:
        Logical                max        current
        cylinders        16383        16383
        heads                16        16
        sectors/track        63        63
        --
        CHS current addressable sectors:   16514064
        LBA    user addressable sectors:  268435455
        LBA48  user addressable sectors:  625142448
        Logical/Physical Sector size:           512 bytes
        device size with M = 1024*1024:      305245 MBytes
        device size with M = 1000*1000:      320072 MBytes (320 GB)
        cache/buffer size  = 8192 KBytes
        Nominal Media Rotation Rate: 5400
Capabilities:
        LBA, IORDY(can be disabled)
        Queue depth: 32
        Standby timer values: spec'd by Standard, with device specific minimum
        R/W multiple sector transfer: Max = 16        Current = 0
        Advanced power management level: 128
        Recommended acoustic management value: 128, current value: 254
        DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4
             Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
        Enabled        Supported:
           *        SMART feature set
                    Security Mode feature set
           *        Power Management feature set
           *        Write cache
           *        Look-ahead
           *        Host Protected Area feature set
           *        WRITE_BUFFER command
           *        READ_BUFFER command
           *        NOP cmd
           *        DOWNLOAD_MICROCODE
           *        Advanced Power Management feature set
                    SET_MAX security extension
                    Automatic Acoustic Management feature set
           *        48-bit Address feature set
           *        Device Configuration Overlay feature set
           *        Mandatory FLUSH_CACHE
           *        FLUSH_CACHE_EXT
           *        SMART error logging
           *        SMART self-test
           *        General Purpose Logging feature set
           *        WRITE_{DMA|MULTIPLE}_FUA_EXT
           *        64-bit World wide name
           *        IDLE_IMMEDIATE with UNLOAD
           *        Segmented DOWNLOAD_MICROCODE
           *        Gen1 signaling speed (1.5Gb/s)
           *        Gen2 signaling speed (3.0Gb/s)
           *        Native Command Queueing (NCQ)
           *        Host-initiated interface power management
           *        Phy event counters
                    DMA Setup Auto-Activate optimization
                    Device-initiated interface power management
           *        Software settings preservation
           *        SMART Command Transport (SCT) feature set
           *        SCT Read/Write Long (AC1), obsolete
           *        SCT Write Same (AC2)
           *        SCT Error Recovery Control (AC3)
           *        SCT Features Control (AC4)
           *        SCT Data Tables (AC5)
                    unknown 206[12] (vendor specific)
                    unknown 206[13] (vendor specific)
Security:
        Master password revision code = 65534
                supported
        not        enabled
        not        locked
        not        frozen
        not        expired: security count
                supported: enhanced erase
        96min for SECURITY ERASE UNIT. 96min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 50014ee2ada79d77
        NAA                : 5
        IEEE OUI        : 0014ee
        Unique ID        : 2ada79d77
Checksum: correct
ubuntu-kylin@ubuntu-kylin:~$

wangbolizhong

没成功，sudo hdparm -iI /dev/sd?  看到主固态硬盘和U盘看不到光驱位置的问题硬盘。在Ubuntu里可以访问那块盘，还要不要试一下windows下的方法？@z75h
把光驱位的拆下来装主硬盘位置试试？

wangbolizhong

z75h 发表于 2015-1-16 07:35
U盘？这个西数320GB是移动硬盘还是光驱位的硬盘呢？
昨晚只注意到留言，没看到帖子。

320G是装Ubuntu的移动硬盘.
光驱位问题硬盘是开机后插进去的,不然不能开机.

wangbolizhong

以管理员身份运行“关闭硬盘PUIS（以管理员身份运行）.cmd

wangbolizhong

按照下面的试了一下可以了.......马丹吓死爹了
https://bbs.pcbeta.com/viewthread-1561762-1-1.html
1. Make bootable pendrive with DOS
一、将DOS写入可引导的U盘
文件在此。
Dos启动三个基本文件，用UltraISO→文件→打开该文件，然后接入U盘，选择写入硬盘映像。
  setup98.rar (689.73 KB, 下载次数: 457, 售价: 1 PB币)

2. Put HDAT2_50.EXE on your pendrive
二、把 HDAT2_50.EXE复制到你的U盘里。
文件见13楼，西日光的帖子。
3. Boot from USB
三、从U盘启动

4. Type HDAT2_50.EXE /W
四、在DOS环境下输入命令：HDAT2_50.EXE /W

5. Reboot.
五、重启计算机